Tiling trowels which trowel to use

Your help would be appreciated! Those would be the two that I recommend. You might try one of each and see which one works better. Our handyman contractor installed a niche on outside wall. He did not put form board behind it.

Do I need to remove durarock and reinstall with foam board and re install durarock. I am concerned as it is a outside wall. Or what other options could I do? It should be fine. Found my answer quickly and it was simply your basic comment: more thinset is better than less. Thanks again for common sense approach to problems and God bless you and your endeavors.

All pcs. I will be using a custom building product tile lab surface guard on each individual surface face of the tile before tile placement. Custom building products recommended their FlexBond thinset for bonding the tile to the hardibacker moisten the hardibacker before spreading their thinset. Custom recommends using their polyblend unsanded grout to finish.

The grout line is going to be so thin, should I be using a grout bag to directly insert the grout into the tile joint? I question the use of an unsanded grout. Unsanded grout should only be used with tight grout joints. Sometimes it makes sense to leave a little extra in the middle to compensate for the curvature of the tile. Will installing more studs eliminate that?

Also installing new valve body. How much of the plaster ground should be protruding from durock before I start tiling. Also what size spacers between tiles would look best. Does thickness of mortar play a large part of overall depth. If your framing meets code, which is 16 inches on center, then the backer board should be fine.

You can always add more supports if you want. Most plumbers will set them to the minimum expected depth. I am using 20 inch X 20 inch polished natural stone tile on my shower walls. For showers, is there a thin-set at the big lot stores you recommend? I would use a white LFT mortar from the big box store. Is this the same thing? First — great site. Thank you for putting this together.

We have a question regarding Tile Leveling Systems. As part of them permanently remains under the tile, can some of them require a slightly thicker notch? Here is our project and application materials. We have not yet selected a tile level system but will want one that has a tool, rather than just clips and wedges.

Yes, some of the bases are thicker than others and could require more mortar. However, I tend to only use leveling systems with large tiles. The homeowner wants no grout lines. After the install it looks like crap because of all the crowning and not even joints. Now I understand why. This has been very informative and I thank you. Rick at qualified maintenance. You need this post: How to install tile of different thicknesses flush, flat, and even with each other.

Where did the. Should that be. It might be cut in half because of the teeth of the trowel. The main thing is to get them as flat as you can. Use Schluter sheine as your transition. It looks times better than butting tile up to hardwood and a small difference in height will not be noticed.

I am installing ceramic tiles mm x mm x mm onto a kithen wall. What size trowel would you recommend? Will be using your affiliate links! Additionally, premixed adhesive is only for use over drywall in non wet areas. The minimum thickness is whatever gives you full coverage under the tile. Just checking. It depends on how thick the mosaics are, what the underside depressions are like, and how thick the mortar is but I would try for the square notch and see how that goes.

If you get a little mortar between the joints you can use a brush with water and a sponge to get it off. Those are big tiles! Hi, I am installing 8x 16 ceramic tile on the wall. What size trowel should I use? I would appreciate your help, thx. But because of the angle of trowel, as was nicely explained, the result will be roughly 0. Or… you could start out saying the ridges would only be 0. Hi, enjoying all the information on your site, thanks for taking the time to help us.

Finally the last option would be to install another layer of go board over existing board to take up the space. What would you suggest, thanks. You definitely want the GoBoard sticking out past the flange because the surface of the board is the waterproofing. The waterproofing has to be past the flange. So, remove the board and shim it out or, I suppose, you could add another layer of board over the surface. Ok, I figured it was a shot in the dark to use a thicker layer of thinset.

The two side walls were out of plumb over an inch and i spent the time to get them right, i want to make sure my time isnt wasted leaving it as is then. Thanks for your help have a great new year. Please help! You can always go a size higher or lower if need be. Hi Jim. Or am I applying a substantial layer? What this does is fills in the depressions but also forces the mortar into the tile. Your email address will not be published. Business Inquiries Privacy Policy.

Consequently, I get asked about trowel sizes quite a bit. Read more Table of contents Why does trowel size matter? What size trowel for mosaic tile? What size trowel for penny tile floor? See Trowel at Amazon. See trowel at Amazon. Comments Hi Jim!

Thank you for the help and great site! But you always have to make your own assessment. Also a U notch lays down less thinset than the same size square notch. It makes for a messy installation as the mortar will come up through the grout joints. So I think the question to ask is: Am I getting enough mortar under my tile?

By mixing the mortar thicker you can probably negate this result. Other than that… : Thanks for the tips on the accent strips. Good idea, there. Depends on how thick and what the back of it looks like. The size of the trowel determines the amount of mortar underneath the tile to support it.

Crossposting from the john bridge forum, sorry. Many tile installers like to use the U-notch who prefer to spread out their wall tile thinset out a little on the heavy-side, or for those that like to spread out their floor tile thinset a bit on the light-side. The difference in the amount of thinset spread out between the square-notch and the slanted-notch is not significant.

The major difference is how the thinset lies. February 19, Steve Sprung. Trowels with U-Notched Notches:. The U-shaped teeth allows them to spread more mortar compared to the V-shaped trowels. They typically dispense more mortar than the other two, and their square or rectangular notches create mortar rows with flat spaces between them. Square-Notched trowels are usually used for most floor tiles. Tip: The general rule is to use a v-notch for a Mosaic tile and a Square-notch for large format tile.

Most average-sized tiles will benefit most from using a U-notch or Square-notch trowel, as the difference in adhesive spread is minimal. Keep in mind that by using too little adhesive, you run the risk of broken or cracked tiles, while too much can create a mess and be a major pain to remove. In order to apply the proper amount of adhesive, your trowel size will depend on three factors;.

Once you have these factors determined, make sure to understand how trowels are measured. Generally, with V-notch trowels, you will see that there are two numbers to factor in, measuring the width and the depth of the notch. On the other hand, with Square or U-notch trowels usually come with three numbers to consider : the first number is again the width of the notch , second is the width of space between the notches which is not a factor in V-notch trowels and finally, the depth of the notch.

You can find this information in the product specifications of most trowels. Tip: If a trowel has only two numbers, it means that the width of the teeth and width between the teeth are the same. One of the good ways to confirm the correct notch size is to install several tiles and then lift them and check if enough mortar contacts the surface of the tile and subtract. Ok, you have all your details in place, but what trowel do you actually need?

Fabrique Blue Grey Chevron Glass Mosaic Tile - mosaic tile sheets may vary, but include smaller tiles on a mesh that benefits from the smaller gaps in mortar made by a v-notch trowel. Brick Brooklyn Blanco - 4. Dover Almond and Dover Almond Deco -